Post by dwilk001 on Jan 29, 2024 14:11:00 GMT -5
Good afternoon,
This is my first time posting to the forum. I have looked around for answers to my problem in the trouble shooting area of the forum but have had no success in finding the correct settings for my RichAuto Controller. I have found settings for the older controllers and have attempted to use some of the data but to no real succes. Long story short, I went in to review some settings in the controller and ended up deleting all the files including the bak file for the controller with the Axiom factory settings. I have reached out to support at Axiom for the data.bak file, but have yet to hear from them as of yet so I wanted to see what I can learn from here.
As mentioned, I did find some of the settings for other models of controllers, and thought I was getting everything running until I went to process a file. When I process one of my files (.mmg) the project was a 16" x 16" x .75" cut out of a state. Everything loaded fine and I used the puck to get my toolset, but when I ran the file everything was made larger and the depth of the project was off (should have been .75" or about 19mm but controller showed and ran it at 39mm so the tool never hit wood). The length and width of the project showed correct at about 397mm but the machine ran it at about 515mm (estimated ans it was about 4" over the size it should have been), so I am lost there and am thinking it is in the controller settings but not sure as I am far from being an expert at it.
Some of the particulars of what Im running are below:
Machine - AR16 Elite
Hand Controller is a - Rich Auto - Auto Now - B581E-1
Version - T8-248
Product ID - A0195310
Soft Version - A1.5656
I am working with VCarve Desktop 11.0 right now and plan to us Aspire later.
Was wondering if someone had their controller settings for the Rich Auto B581E-1 written down or if someone would be able to email me a data.bak file (if possible and not frowned on).
Thanks for reading and for any help anyone can provide.
DOL
Dave
This is my first time posting to the forum. I have looked around for answers to my problem in the trouble shooting area of the forum but have had no success in finding the correct settings for my RichAuto Controller. I have found settings for the older controllers and have attempted to use some of the data but to no real succes. Long story short, I went in to review some settings in the controller and ended up deleting all the files including the bak file for the controller with the Axiom factory settings. I have reached out to support at Axiom for the data.bak file, but have yet to hear from them as of yet so I wanted to see what I can learn from here.
As mentioned, I did find some of the settings for other models of controllers, and thought I was getting everything running until I went to process a file. When I process one of my files (.mmg) the project was a 16" x 16" x .75" cut out of a state. Everything loaded fine and I used the puck to get my toolset, but when I ran the file everything was made larger and the depth of the project was off (should have been .75" or about 19mm but controller showed and ran it at 39mm so the tool never hit wood). The length and width of the project showed correct at about 397mm but the machine ran it at about 515mm (estimated ans it was about 4" over the size it should have been), so I am lost there and am thinking it is in the controller settings but not sure as I am far from being an expert at it.
Some of the particulars of what Im running are below:
Machine - AR16 Elite
Hand Controller is a - Rich Auto - Auto Now - B581E-1
Version - T8-248
Product ID - A0195310
Soft Version - A1.5656
I am working with VCarve Desktop 11.0 right now and plan to us Aspire later.
Was wondering if someone had their controller settings for the Rich Auto B581E-1 written down or if someone would be able to email me a data.bak file (if possible and not frowned on).
Thanks for reading and for any help anyone can provide.
DOL
Dave
