|
|
Post by Steve White on Aug 25, 2019 15:56:51 GMT -5
I have searched these threads and not found exactly what my machine is doing. During running a tool path it will stop as if it has finished the tool path, showing the "User will finish" in the controller screen. There is no rhyme or reason to the points that it stops. It has however grown much more frequent. I can move from the X-Y 0 and it will say that the zero has not been set. Go ahead and reset and it will run from the beginning of the tool path until it stops again...randomly. Sometimes it will say there is no data on the u-disk. sometimes it says there is no u-disk. Then it will start reading and work well for maybe the next two or three tool paths.
Things that I have tried;
Remove the u-disk and re-insert
Turn of the machine and re-start
Disconnect the power for 15-60 minutes and re-start
Turn off over night and restart
Threaten the machine
Beg the machine
Anyone have any ideas or a similar situation?
|
|
|
|
Post by gerry on Aug 25, 2019 16:31:00 GMT -5
How about some basics like what machine and how old???
|
|
|
|
Post by Mezalick on Aug 25, 2019 16:32:59 GMT -5
I have searched these threads and not found exactly what my machine is doing. During running a tool path it will stop as if it has finished the tool path, showing the "User will finish" in the controller screen. There is no rhyme or reason to the points that it stops. It has however grown much more frequent. I can move from the X-Y 0 and it will say that the zero has not been set. Go ahead and reset and it will run from the beginning of the tool path until it stops again...randomly. Sometimes it will say there is no data on the u-disk. sometimes it says there is no u-disk. Then it will start reading and work well for maybe the next two or three tool paths. Things that I have tried; Remove the u-disk and re-insert Turn of the machine and re-start Disconnect the power for 15-60 minutes and re-start Turn off over night and restart Threaten the machine Beg the machine Anyone have any ideas or a similar situation? How about saving the file to the internal memory....It may be a Flash / thumb drive issue... Michael |
|
|
|
Post by stevew on Aug 25, 2019 17:57:59 GMT -5
How about some basics like what machine and how old??? It is an Ar8 Pro and it is about three weeks old. |
|
|
|
Post by gerry on Aug 25, 2019 20:24:33 GMT -5
Sounds like it's time to call Chad on Monday. I've never seen 'User Will Finish'
|
|
|
|
Post by stevew on Aug 25, 2019 20:29:53 GMT -5
Sounds like it's time to call Chad on Monday. I've never seen 'User Will Finish' Ok, thanks for looking. The message comes on when I finish a tool path, the spindle will raise and stop and this message is highlighted at the bottom of the screen. If you press "ok" it will return to X-0Y-0. |
|
|
|
Post by redwood on Aug 28, 2019 10:52:23 GMT -5
I had this happen to me, the result was I had to replace the controller. Initial thought my Axiom was that it might be caused by static electricity.
|
|
johnb
Full Member
New owner @ March 2019, AR16 Elite, Aspire, 4th Axis & Laser
Posts: 326
|
Post by johnb on Aug 28, 2019 14:06:44 GMT -5
What software? What Post Processor?
Have you tried re-saving the file and re-running the Post Processor? Save it with a different file name.
If you're running it from the flash disk, have you tried loading it to the controller memory and running it from there?
|
|
kyle
New Member
Posts: 1
|
Post by kyle on Aug 29, 2019 18:26:35 GMT -5
Sounds like it's time to call Chad on Monday. I've never seen 'User Will Finish' Ok, thanks for looking. The message comes on when I finish a tool path, the spindle will raise and stop and this message is highlighted at the bottom of the screen. If you press "ok" it will return to X-0Y-0. this has happened to me a few times as well. I have an AR6 Basic, about 5 months old. |
|
|
|
Post by stevew on Sept 2, 2019 12:39:08 GMT -5
I have searched these threads and not found exactly what my machine is doing. During running a tool path it will stop as if it has finished the tool path, showing the "User will finish" in the controller screen. There is no rhyme or reason to the points that it stops. It has however grown much more frequent. I can move from the X-Y 0 and it will say that the zero has not been set. Go ahead and reset and it will run from the beginning of the tool path until it stops again...randomly. Sometimes it will say there is no data on the u-disk. sometimes it says there is no u-disk. Then it will start reading and work well for maybe the next two or three tool paths. Things that I have tried; Remove the u-disk and re-insert Turn of the machine and re-start Disconnect the power for 15-60 minutes and re-start Turn off over night and restart Threaten the machine Beg the machine Anyone have any ideas or a similar situation? How about saving the file to the internal memory....It may be a Flash / thumb drive issue... Michael |
|
|
|
Post by stevew on Sept 2, 2019 12:40:35 GMT -5
Mezalick You were right! After I saved it to the controller it worked perfectly. Thank you for your help.
|
|
